How To Repair The End Of A Hose

Garden Hose Repair: iv Fast (and Frugal) Fixes

Repair rather than replace your most essential lawn care accessory with these quick and like shooting fish in a barrel techniques.

Photo: istockphoto.com

When intact, your garden hose is a trusty tool for hydrating your backyard, rinsing debris from your deck, and just about every exterior task requiring h2o. Only a aptitude, torn, or otherwise leaky hose wastes water and makes outdoor chores more difficult. Plus, you often merely discover there'southward a problem after you've started a job when running out to buy a new hose is darned inconvenient. Fortunately, it's adequately piece of cake to extend its life by repairing a garden hose with the smart (and cheap!) DIY fixes nosotros've assembled here. Read on to learn more about garden hose repair.

RELATED: seven No-Kink Garden Hoses That Examination True

1. Seal small holes with electrical tape.

Pesky pinholes are often but visible to the eye when you lot connect the water and spot small, geyser-similar spurts of water from the punctured section of the hose. Such small leaks can direct water away from the lawn or plants you're aiming for—not to mention squirt y'all in the centre! Electrical tape, usually fabricated of a PVC bankroll and a condom-based adhesive, has the elasticity, insulation, and weather condition resistance needed to effectively plug these holes, only you lot may somewhen need a hose mender (meet below) if leaks persist.

Plow off the water, disconnect the hose, and wipe it dry out with a rag. Mark the punctured section with a mark, and so wrap electrical record around the marked section, overlapping a few times to ensure skillful adherence. Take intendance non to wrap so tightly that the hose creases, as this might impede water menstruum. Reconnect the hose to the spigot or a spray nozzle and plow on the water to verify that you've solved the problem.

Photo: istockphoto.com

2. Repair large tears with a hose mender.

Larger tears in a hose frequently result from snagging on a tree or bush-league, cracking with exposure to extreme heat or cold, or chewing by a naughty pet. Water will gush from such tears when y'all turn on the tap, but a hose mender—a brusk plastic or metallic tube that replaces the damaged section, available (e.g., Nelson Compression Fit Hose Mender on Amazon)—can come up to the rescue.

Turn off the h2o, disconnect the hose, and remove the torn section with a hose cutter or garden shears. Attach the cut ends of the hose to the connectors of the hose mender, twisting the two collars on the mender clockwise to tighten. Reconnect the hose to the spigot or a nozzle and turn on the water to verify there are no leaks.

3. Set a leaky coupling with a new hose gasket.

1 of the peskiest garden hose bug is a leak in the coupling: the metal or plastic fitting found on both ends of a hose used to connect the hose to the spigot, a nozzle, or a sprinkler. If yous spot a steady drip coming from the hose couplings when you connect it to a source, the gasket may need to be replaced. Gaskets naturally wear with time and water exposure, so program to switch out your hose gaskets every three to 10 years.

Turn off the h2o, disconnect the leaky hose cease, and use needle-nose pliers to pull out the existing gasket inside the coupling on that hose end. Use your fingers to push the new gasket within the hose coupling. More often than not, the thicker O-band gaskets (eastward.chiliad., Nelson O-ring, bachelor on Amazon), the more watertight the seal; flat gaskets don't mold to the contours of the coupling quite too. Reconnect the hose to a spigot or nozzle and plough on the h2o to ensure the coupling no longer leaks.

Photograph: istockphoto.com

RELATED: The All-time Hose Nozzles for Your Gardening Needs

4. Replace a bent coupling with a new hose coupling.

If the coupling on either end of the hose continues to leak later a gasket replacement, the coupling may have gotten physically misshapen by a run-in with a backyard mower or other piece of heavy equipment. A bent coupling loses the watertight seal between the hose and a spigot, nozzle, or sprinkler, causing a leak.

Replacing a bent coupling with a new one that suits your needs will provide a permanent solution for the leak. There are two types of couplings: female person (e.g., Nelson Female person Hose Repair, available on Amazon) connects to the spigot and male person (e.g., Nelson Male person Hose Repair, available on Amazon) connects to a nozzle or sprinkler. Too be sure to choose a coupling with the same diameter every bit that of your hose (eastward.g., 5/8-inch coupling for a 5/8-inch-bore hose). Both the coupling type and diameter will be stated on the packaging.

Turn off the water, disconnect the hose, and remove the entire bent coupling with a hose cutter. Push the exposed end of the hose into the connector of the coupling, and so twist the collar of the coupling clockwise to tighten it. Connect the hose to a spigot or nozzle and plow on the water to ensure the coupling doesn't leak.

Photo: istockphoto.com

Safeguard your hose to avert future harm.

Employ these tips to stave off hereafter damage to your garden hose and ensure leak-free backyard maintenance:

• Avoid leaving a hose outside in farthermost heat or common cold. Existing creases in a hose can progress into cracks with exposure to high heat or if cold water within the hose freezes. A cool, dry environment similar the garage is all-time for hose storage.
• Lightly curl and shop your hose on a hose cart (e.g., Ironton Hose Reel Cart, available on Amazon) when not in utilize to keep it kink-free (creases tin eventually lead to tears). A hose cart will besides make it easier to transport your hose to and from the garage or shed to the backyard without the hose snagging on trees or bushes, equipment, and other precipitous objects or abrasive surfaces that can crusade holes or tears in it.
• Drain any remaining water in a hose after a watering session past spraying information technology out with a nozzle and then lifting and gently shaking the hose with the hose end facing downwards to remove any leftover water. Standing water tin can weather the gaskets inside the hose and reduce the integrity of their seal over time.

If you must replace your hose, cull one fabricated of rubber instead of vinyl. Rubber hoses tend to be more resistant to temperature changes and are less likely to crack over time than vinyl equivalents.

RELATED: The Best Hose Timers for Your Lawn-Care Needs

Source: https://www.bobvila.com/articles/repairing-a-garden-hose/

Share this post